| Quartz infrared tubes utilize new infrared technology in Comfort Furnace Infrared Heaters. |
| New stainless steel diffusers produce 14% more heat than last year’s models. |
| Designed to last 20,000 hours minimum instead of the standard 5,000 hour rating on most other infrared bulbs. |
| New ceramic and stainless quick-connect terminals provide for easy servicing. Tubes can be replaced in three minutes or less without special skills. When a tube needs to be replaced we ship the new tube to you with a service reimbursement voucher so you never have to be without your heater. This avoids the 3-4 week turn-around time required to ship a heater back to the manufacturer for warranty or repair. |
| New Comfort Furnace heat exchanger provides enhanced copper ionization. This leads to maximum conversion of infrared wave into a more absorbent bandwidth of infrared. (9-10 micron) |
| Comfort Furnace heaters have a 3-year extended manufacturer’s warranty. |
| Comfort Furnace heaters have Solid-state Electronics – No more mechanical contact switches or sensors to wear out. |
| Comfort Furnace heaters have a full function electronic Thermostat – This new thermostat replaces the standard mechanical thermostat found on other brands. Provides sensitive control of room temperatures to 1 degree. |
| Comfort Furnace heaters have a Delayed Start Function – you can delay when your heater turns on up to 23 hours from the time you set it which provides versatility and additional energy efficiency. |
Safe
Portable heaters are a major cause of residential fires in
the United States. The Comfort Furnace
heater, however, cannot cause a fire. That’s because the quartz infrared heating
elements are
confined inside a fireproof heat exchange. So the outside remains cool to the
touch. In fact,
when it’s operating pets can sleep on it without harm.
Unlike kerosene, gas or wood heating, The Comfort
Furnace doesn’t require excessive ventilation
(cold air coming into the house) for safe operation. This leads to increased
heating efficiency and
no combustion by-products.
Healthy Heat
The Comfort Furnace heater provides a healthier heat.
That’s because unlike other heating sources, it will not reduce the humidity or
oxygen content in the room. Your sinuses and skin won’t be dry like with typical
heating sources. Gone is the suffering from increased lethargy or sleepiness.
It’s all thanks to an intelligent unit that doesn’t destroy and leaves negative
ions intact.
In addition, all Comfort Furnace Quartz Infrared
Portable Heaters are equipped with a 3-micron
reusable filter system that removes airborne particles as air is pulled into the
heating system.
The heat exchanger in a Comfort Furnace heater destroys bacteria, viruses, mold,
mildew,
and other air-borne pathogens before the heated air leaves the unit.
Zoned Heating
By using individual controlled units, the Comfort Furnace
heater provides heat only where and when it is needed. Portable zoned heating
produces economical heating for maximum energy savings by heating only the areas
that you desire to heat.
The Comfort Furnace heater comes with accurate electronic thermostat controls and a delayed start function to provide accurate comfort settings and minimize energy costs when you’re not at home.
Its infrared heater is less expensive to operate per square foot than other forms of electric or gas heat.
The Comfort Furnace heater uses a standard 115volt household current, and requires no special 220volt wiring, chimney vent or expensive duct installation.
Ultimate Comfort
No longer will you face the old hot spot/cold pocket
syndrome. With the Comfort Furnace™ heater you get even heat distribution. It is
thermostatically controlled, and circulates and recycles heated air from floor
to ceiling so the temperature differential is minor. Which means there’s no need
for a ceiling fan.
As the Comfort Furnace™ heater operates, you will notice that its heating ability does not depend on a high-speed flow of air. Instead, the gentle airflow allows for better air mixing inside the unit leading to more effective heating action.
Operation
Just plug the power cord into any 115 volt 15 amp
receptacle. Push the power button and then set the thermostat to the desired
temperature. That’s it. The Comfort Furnace™ heater will do the rest. The first
DC fan will turn on during the warm-up cycle. Once the infrared quartz heating
elements have warmed up (about 2 minutes) the second fan will turn on. The
result? You get an additional soft, heavenly heat for maximum efficiency and
comfort. Talk about simple comforts.
Comfort Furnace Oak Comfort Furnace Walnut Comfort Furnace Black
Heat-A-Lot Oak Heat -A-Lot Black